hiking emile Geplaatst 22 augustus 2009 Geplaatst 22 augustus 2009 Ik krijg mijn colorado 300 niet meer opgestart. Ik krijg het bericht "memory full" endan gaat hij weer uit. Ik krijg hem ook niet aangesloten op de laptop, zelfde probleem. Heb op google gekeken en dat zag er niet goed uit. Er schijnen veel mensen met het zelfde probleem te zitten. Ik hoop dus hier misschien een oplossing te vinden. bij voorbaat dank.
Lepman Geplaatst 22 augustus 2009 Geplaatst 22 augustus 2009 Staat er in de handleiding geen 'harde reset'?
Cernunnos Geplaatst 22 augustus 2009 Geplaatst 22 augustus 2009 Heb je recent updates oid gedaan? Gebruik je een geheugenkaart? wat is er veranderd sinds de laatste keer dat hij wel werkte? Je kunt altijd hier kijken voor meer info. Als je er niet uit komt laat het dan nog maar even weten. succes!!
hiking emile Geplaatst 22 augustus 2009 Auteur Geplaatst 22 augustus 2009 Nee, heb niets veranderd. Heb vandaag gewandeld en na terugkomst wilde ik de cachen loggen en dan dit probleem.
hiking emile Geplaatst 22 augustus 2009 Auteur Geplaatst 22 augustus 2009 Heb even door de lijst gekeken maar daar staat het antwoord helaas niet bij.
Lepman Geplaatst 22 augustus 2009 Geplaatst 22 augustus 2009 Misschien heb je er te veel gedaan dat de memory vol is?
Toyeco Geplaatst 22 augustus 2009 Geplaatst 22 augustus 2009 Misschien heb je er te veel gedaan dat de memory vol is?
Broosha Geplaatst 22 augustus 2009 Geplaatst 22 augustus 2009 Dat lijkt een intern hardware probleem. Om daar echter zeker van te zijn (en zoals Cernunnos ook vraagt) gebruik je een gehuegen kaart? Zo ja, verwijder deze en vervang deze eens met een ander (lege) Blijft het probleem dan bestaan?
Peetee Geplaatst 22 augustus 2009 Geplaatst 22 augustus 2009 Op http://garminoregon.wikispaces.com/Miscellaneous kwam ik dit tegen. Zou dat kunnen helpen? M3.) Is there any way to recover a corrupted Oregon without sending it back to Garmin? Warning: This procedure may delete information (waypoints, routes, tracks, etc) from your GPS and settings may be set back to factory defaults. It is intended to be a "last ditch" recovery procedure. There are two recovery procedures you can try on your Oregon. The first can be use to resolve problems where the unit cannot boot because it gets stuck loading maps or gpx files that might be corrupted. The second procedure can be used to recover a unit which will not start properly after software upgrade. Recovery #1 -- Forced USB Mass Storage Mode (only available in release 2.85 and after) If your Oregon freezes during the startup process (i.e. Loading Maps...), and you've just loaded new maps or new gpx files then it could be the new files which are causing the problem. This procedure forces the unit into USB Mass Storage mode so that you can delete (or rename) these files. Follow these steps to recover: •Attach the Oregon to your computer via USB cable •The Oregon will power on and start to boot, immediately power the unit off while still connected •Power on the Oregon and continue to hold down the power button for 30 seconds •The Oregon should enter USB mass storage mode •From your computer remove or rename any gpx or map files (.img) files that were recently added •Unplug the Oregon and power on to see if this remedies the problem Recovery #2 -- Forced Upgrade to 2.5 This procedure may be useful if you've recently performed an upgrade an the unit no longer works. The procedure will perform a low level installation of the software. After running this procedure the Oregon will be running Software version 2.5 so it may be necessary to run the Webupdater once you are done to upgrade to the newest version of software. First you'll also need to download Updater.exe and 2.50_Update.zip. Once you've downloaded these files save them into a directory such as C:\Garmin on your PC and unzip the zip file. This should leave you with two files: C:\Garmin\Updater.exe and C:\Garmin\BO79500F.rgn. On your PC click the Start menu, select "Run..." and type "cmd" where it says open. A black window with a DOS command prompt should appear. At the command prompt enter the following command: > cd c:\Garmin At the next command prompt type the following command without hitting enter: > Updater.exe B079500F.rgn Now back to your Oregon. 1.Disconnect the Oregon and make sure it is powered off 2.Press and hold down the power button 3.Quickly plug the GPS into your USB cable connected to your PC while still holding the power button down. 4.Back on the PC hit to execute the command above - still holding down the power button on the Oregon 5.This should bring up the Updater window, you'll need select the USB radio button - still holding down the power button on the Oregon 6.Wait for the "Loader" banner at the top of the Oregon screen above the Garmin logo and release the power button 7.The GPS should display "Software Loader" and Updater should show a download progress bar. 8.The GPS will go through several update / restart cycles. 9.If everything goes well the Updater will give a success message and the Oregon will restart running Software version 2.5 10.Run Webupdater to make sure that the unit has the most up to date software. If you don't perform steps 2-4 within about 30 seconds the Oregon will end up in USB mass storage mode. If this happens you will need to start over. In step 6 you have just a split second to release the power button at the right time. When you plug the Oregon into the computer in step 3 you might be asked to install the Garmin USB drivers if this is the first time you have executed this procedure. Allow your PC to automatically update the drivers which should be available on your PC if you've installed Mapsource. If not the USB driver can be downloaded from Garmin.
Cernunnos Geplaatst 22 augustus 2009 Geplaatst 22 augustus 2009 Voor de oplossing kijk hier Verder weet ik niet of je je colorado al hebt voorzien van de nieuwste firmware etc. Dit lost zover ik kan nagaan ook het probleem op zover ik heb kunnen nagaan. (tenzij je natuurlijk echt het geheugen vol hebt zitten LOL) Laat maar horen of je er uit bent of niet. grtzz
hiking emile Geplaatst 23 augustus 2009 Auteur Geplaatst 23 augustus 2009 Het is gelukt Cernunnos. Het is niet helemaal gelopen zoals de beschrijving het aangaf, maar hij gaat weer. Ik heb alles volgens de beschrijving gedaan. Hoe weet ik nu welke firmware erop staat en heb ik een andere nodig? Nu gaat mijn Garmin weer,dus.......In iedergeval bedankt, ik kan weer gaan cachen. Groet Hiking Emile
Cernunnos Geplaatst 23 augustus 2009 Geplaatst 23 augustus 2009 Het is gelukt Cernunnos. Het is niet helemaal gelopen zoals de beschrijving het aangaf, maar hij gaat weer. Ik heb alles volgens de beschrijving gedaan. Hoe weet ik nu welke firmware erop staat en heb ik een andere nodig? Nu gaat mijn Garmin weer,dus.......In iedergeval bedankt, ik kan weer gaan cachen.Groet Hiking Emile Via het programma 'Garmin web updater' wordt je gps al gecontroleerd op het up to date zijn. Nieuwe firmware komt daar echter niet altijd in naar voren, de zo genaamde beta's die wel degelijk goed werken. Die zul je van de site zelf moeten downloaden en er handmatig opzetten. In de colorado zelf kun je zien welke software en gps software versie je draait via instellingen -> systeem -> opties -> softwareversie deze info is ook in de link te vinden die ik eerder noemde. grtzz
hiking emile Geplaatst 23 augustus 2009 Auteur Geplaatst 23 augustus 2009 Heb er nu software versie 2.90 opstaan
Cernunnos Geplaatst 23 augustus 2009 Geplaatst 23 augustus 2009 (bewerkt) De GPS-software versie is goed, 2.90 die je nu hebt. De andere versie is de nieuwste 2.95 van. Is een beta maar werkt hier zonder problemen. Lees er verder ook geen problemen over op internet. Mocht je die firmware gaan updaten even twee dingen: 1) maak een backup van je garmin 2) verwijder alle gpx bestanden voor de update en zet die er later weer op. Ik heb er geen problemen mee gehad maar lees dat er mensen wel problemen door kregen. succes!! 23 augustus 2009 bewerkt door Cernunnos
Aanbevolen berichten